Humax 5400 Service Manual

What is PMCTable?

The PMCTable(Row 1-140000 in the firmware) is used to set the PID for incoming ECM-Data(Entitlement Control Message) for the Provider Channel in order to Decrypt the Channel. A Service Channel might have more than one CA-ID(Viaccess, i****o…) with different Idents, so you may find more than one row for the same Channel.

In addition, ToH firmware adds specific rows on PMCTable for their own use.

It is not so simple as describe above; I will give an example to clear it more.

PMCTable row contains:
Ant ID: ID/Number of the Satellite position in your Channels List Settings.
Service ID: Identification of the Service (Giving by the Provider)
CA-ID: Identification of the Encryption system used by this Service
---0100 – Seca
---0500 – Viaccess
---06xx - i****o (xx Different Encryption Version of i****o)
---17xx – BetaCrypt (xx Different Encryption Version of Betacrypt)
---18xx - Nagra(xx Different Encryption Version of Nagra)
---0Dxx - Cryptoworks(xx same)
---0B00 – Conax
---…etc
ECM: Identification of the Channel
Ext/ID: Provider Identification
To: Time Offset to correct time difference in channels.
---FFFD = -3.00
---FFFE = -2.00
---FFFF = -1.00
---0000 = 0:00
---0001 = +1.00
---0002 = +2.00
---0003 = +3.00
Audio/Video ID: Identify the Audio and/or Video ID.
---A+VPID: Check both Audio & Video
---VPID – Only Video
---APID – Only Audio
---OFF – No check
---No PCR – PCR PID disabled
Try: From where trying to decrypt the Channel.
---All – All below
---Emu – Emulation
---CRD – Card
---Net – Network

Example for Multivision 3
AntID---ServiceID---CAID---ECM---ExtID---To---AV/PID---Try
===============================================
3----------1302------500------168----007C---0----A+VPID---All


Thanks to paul_kh and CrazySat

HowTo Humax5400 in the c****s network

Here is a small description for Humax Connection to existing c****s network.

HUMAX:
First of all, should be on the Humax Toh the latest software (as of today: 6.2) installed.
Once this thing is in the menu on the Humax Config, the last point on HSIC represent. In addition to CARD + EMU + S set (2 points above).
A card in the Humax slide shaft, over the serial cable Humax to PC. Done.

PC:
HSIC Start Program (current HSIC 3.0)
Under settings the following settings:

[rimg]http://img223.imageshack.us/img223/7141/sanstitre1b.png[/rimg]

IP / Name = IP of the server box or dyndns name (zBmeindyndns.dyndns.org)
Port = The port which the port CS-release runs
User = User name (must be in the server box in the User exist)
Password = Of course, the password of the user

Local-IP = The IP of the PC which is connected to the Humax
Port = 8003 default Simple drinlassen.
COM port = The serial interface register (either 1 or 2, has almost no more)
Then update button once to switch on the box and wait about 10-20 seconds. It should be bright.


@ Elgeneral

how to enable keys in to humax

from our remote go in to vh1 / vh1. / vh1 classic

read how to select keys in to humax
press menu->parser->parser->blue button-> sekect key-> ok button

[spoiler]from our remote go in to vh1 / vh1. / vh1 classic

read how to select keys in to humax
press menu->parser->parser->blue button-> sekect key-> ok button[/spoiler]

How to activate biss keys into humax with out pmct these steps

par example: tun in to rai africa press menu ToH parser blue = edit ->

[spoiler]2600 xxx xxx[/spoiler]

and press ok ro activate.

we will to remember this before we make that turn all biss
keys lokk into the id

[spoiler]2600 xxx[/spoiler]

how put manual file bin?

1 - click on the menu
2 - Click OK to ToH
3 - go on equity Parser then press OK
4 - you open another screen on the left down on equity Ram Editor then press OK
5 - you will find two windows left you will find the highest type of encryption and No. Provider name and bouquet
6 - to determine the type of encryption follow next
Of the extraordinary press the red button
System Viaccess click on the green button
System Nagravision the button yellow
System i****o click on the blue button
System Conax click on the button White
System biss click on the button radio
7 - go on Provider to identify the intended introduction of the code and that it shares the right and the left, if not find Provider required Click on the OK button and enter the new No. Provider
8 - Stand on the line to be introduced by the code and click on OK button
9 - begin introducing logic and type the numbers from 0 to 9 and remote figures for the characters read
Button spare sound symbolizes the characters A
Red button symbolizes the letter B
Green button symbolizes the letter C
Button Yellow symbolizes the characters D
Button Blue symbolizes the letter E
White symbolizes button to the letter F
10 - after the completion of the introduction of logic out of the list and will work with you CHANNELS


@baloota; chris

HTT Humax 5400Z To Plus Converter

HTTZ2P is one of Humax Turbo Suite 2.1 Componets. (Not Published yet).

Build IRCI-5400Z Plus Compatible Firmware from:
ToH3.4_HoTx.x
ToH3.3_HoTx.x
ToH3.2_HoTx.x
HIC10500-ToH3.0/3.1./3.2
Older HIC10500 based firmware HDF.

How To Use
==========
1-Select HDF File.
2-Select HDF Type.
3-Press Convert and save the New Compatible HDF.

Thanks to Crazysat for the Tuner fix.

Enjoy!
Humax Turbo Team

How to get rid of the problem was reaching the upper limit of the channels in Humax


before the start of the search for channels
log in to the list of the organization of networks
must review all existing networks in front of you
if you find one of the networks there is no front channels should be immediately delete this network
after it is better to use the search robot
If you want to use manual searches do not use search through the network

baloota

CCCam on Humax 5400

At last my friend
Our Humax 5400 is now capable to do sharing with CCCam servers

Really I tried it on my Humax 5400Z for few days now and it is working

With the help of a program called "SSSP Plug"

and setting should be
card+s+emu
ecm+emm
sssp

when you extract the program, it will do a folder for itself
also it has a sub-folder called "Plugins"

this Plugins folder has a file called "FLYCCCAM.cfg"
the server is only single line or more written in this file

[rimg]http://img268.imageshack.us/img268/2231/cccam.gif[/rimg]

The program is attached

Hoping to enjoy our Humax and love it more

Regards

Withdrawal of parental code (Reset password)

Top to bottom colored buttons, except for the gray, then "0", then OK

or
1. Go to the "STB Status" in Main menu
2. Press "Red" key -> "Green" key -> "Yellow" key -> "Blue" key ->
"White" key -> "0" key using the RCU in sequence.
3. Pin code will be reset to "0000" automatically.

@ ig0r